How To Make Sliding Closet Doors Out Of Plywood

How To Make Sliding Closet Doors Out Of Plywood

Making sliding closet doors out of plywood is a great way to save money and create a custom closet that fits your needs. You’ll need a saw, a drill, screws, and plywood.

How To Make Custom Sliding Closet Doors

Materials Needed

-1 piece of plywood, 36” wide by 78” long
-6”-thick door hinges
-1”-thick door stop
-Plywood glue
-Ruler or a straight edge
-Circular saw
-High-grit sandpaper
-Stiles
-Plywood screws
-Locking pins

1. Cut the plywood to the desired size and shape.

2. Glue the door hinges to the plywood on opposite ends.

3. Mark the positions of the door stop and the door hinges on the plywood.

4. Cut out the door stop and the door hinges with the circular saw.

5. Sand the edges of the door stop and the door hinges to roughen them up.

6. Drill pilot holes through the door stop and the door hinges.

7. Screw the door stop to the plywood using the plywood screws.

8. Sand the edges of the door stop and the door hinges.

9. Drill pilot holes through the door stop and the door hinges.

10. Insert the locking pins into the door stop and the door hinges.

11. Close the door and test the fit of the door stop and the door hinges.

12. if the fit is satisfactory, screw the door stop and the door hinges to the plywood using the plywood

See also  How To Remove Door Panel Without Opening Door

Cutting The Plywood

Before you can start cutting the plywood, you first need to measure the width and length of the piece you want to make the door out of. Once you have those measurements, use a jigsaw to cut the plywood to the desired dimensions.

Once the plywood is cut, it’s time to start mounting the track. You’ll need two pieces of plywood that are the same width and length as the door you’re making. These pieces should be mounted about 1 inch from each end of the door so that the track can slide smoothly across them.

Once the track is mounted, it’s time to start cutting the holes in the plywood. There are a lot of different ways to do this, but the basic idea is to cut a hole that’s the same size as the dowel that will be used to mount the track onto the door.

Once the holes are cut, it’s time to attach the track to the door. You’ll need to use a dowel gun to insert the dowel into the hole in the plywood and then use a screw to secure it in place.

Now it’s time to install the door. First, measure the distance from the top of the track to the bottom of the door. This will give you the height of the door above the track.

Then, use a circular saw to cut a hole in the top of the door that’s the same height as the track. Make sure that

See also  How To Add Garage Door To Alarm.Com

Assembling The Frame

1. Mark the positions of the header and footer boards on the closet door panels. Measure and mark the corresponding positions on the ends of the 1/2″ x 3″ side rail pieces.

2. Cut the header and footer boards to the marked positions.

3. Cut the side rail pieces to the marked positions.

4. Glue the header and footer boards to the side rail pieces.

5. Glue the side rail pieces to the closet door panels.

6. Nail or screw the closet door panels to the frame.

Hanging The Doors

  1. Make sure the edges of the door are at least 2″ wider than the opening. This will ensure the door swings open and closed smoothly.
  2. Cut the plywood to the desired size. Be sure to allow enough space on the sides and top for the screws and hinges.
  3. Glue and screw the plywood to the wall. Be sure to space the screws evenly so the door is sturdy.
  4. Hang the door using the provided screws and hinges. You will want to make sure the door is vertical and level before hanging.
  5. Test the door to make sure it is swinging smoothly and open and closed properly.

Adding The Hardware

Adding the hardware to your sliding closet doors is very easy. All you need is a pair of screws and a door handle.

The screws go into the door handle and hold it in place. The screws should be about 1 inch from the end of the handle.

The other end of the screw goes into the edge of the door. The screw should go through the door and the screw head should be sticking out the other side.

Now you just need to hold the screw in place while you screw the door handle on. Be sure to tighten the screws evenly so that the door handle doesn’t move.

Finishing Touches

For a really professional finish, you can use a wood sealer or a finishing spray. If you use a sealer, make sure to wait until the end to sand the doors so you don’t lose the sealer.

If you use a spray, apply it to the doors and then use a cloth to wipe it off. The doors will then need to be sanded and finished.

Conclusion

If you want to make a sliding closet door out of plywood, here are the steps:
1. Cut the plywood to the desired size.
2. Attach the plywood to the door with screws or nails.
3. Slide the door open and close it to test it out.
4. If necessary, adjust the screws or nails to make the door fit perfectly.

See also  How To Open Doors In Gmod

Related Posts

Leave a Reply

Your email address will not be published.